Start with what the mirror is built to do
An enhanced aluminum mirror is a reflective surface you want to keep reflective. For Esco Optics' Fused Silica Precision Quality Flat Mirrors, the coating is specified as Enhanced Aluminum with Ravg. > 90% over 450–2000 nm. That wavelength range and reflectivity figure are the performance you are protecting every time you handle, clean or store the optic.
The substrate is fused silica in 25.4 mm and 50.8 mm diameters, polished to 1/10 wave surface accuracy and 40/20 scratch/dig over an 85% aperture. The second surface is ground and all edges are beveled. Those details matter for care because the coated face, the polished aperture and the edge are not interchangeable surfaces.
A handling routine that respects the coating and the edge
The supplied product record does not include a manufacturer cleaning procedure or a list of approved solvents, so the steps below are general good practice for coated precision optics rather than a reproduction of Esco instructions. Where the record is silent, treat the absence as a reason to be conservative, not as permission to improvise.
- Work from the edge, not the face: The beveled edge gives you a place to hold the mirror without touching the coated surface or the polished 85% aperture. Handle the optic by its edge whenever the mount allows it.
- Keep the coated face covered until installation: Leave the mirror in its protective packaging until you are ready to mount it. The 40/20 scratch/dig specification describes the surface quality the optic is supplied to, not a surface that tolerates handling.
- Check the diameter fit before mounting: Diameter tolerance is +0/-0.1 mm, so the mirror is intended to fit a mount sized for the nominal diameter. Confirm the mount and retaining method before you remove the optic from protection; forcing a mirror into an undersized seat puts stress on the edge and coating.
- Handle one optic at a time: Work over a clean, uncluttered surface and keep the mirror from contacting other optics or tools. The second surface is ground, but the first surface carries the Enhanced Aluminum coating and the precision polish.
Specs that shape your care decisions
- Fused Silica Precision Quality Flat Mirrors, Enhanced Aluminum: Enhanced Aluminum coating provides Ravg. > 90% over 450–2000 nm. This is the reflectivity range you are preserving; aggressive cleaning or abrasion risks the coating that delivers it.

Fused Silica Precision Quality Flat Mirrors, Enhanced Aluminum - Fused Silica Precision Quality Flat Mirrors, Enhanced Aluminum: Polished to 1/10 wave surface accuracy and 40/20 scratch/dig over an 85% aperture. The central aperture is the precision zone. Keep handling and cleaning away from it unless inspection shows something that actually needs removal.
- Fused Silica Precision Quality Flat Mirrors, Enhanced Aluminum: Fused silica substrate in 25.4 mm and 50.8 mm diameters, with diameter tolerance +0/-0.1 mm. Fused silica is the substrate, not a license to skip care; the tight diameter tolerance means mounting force should never be used to make a mirror fit.
Cleaning: what the record supports and what it does not
The supplied evidence for this mirror does not include a manufacturer cleaning procedure, approved solvents, wipe directions or drying steps. That is a real limitation: anyone who tells you a specific solvent, number of wipes or drying method is following Esco's instructions for this optic is going beyond what the record confirms.
What the record does confirm is a 40/20 scratch/dig surface specification and an Enhanced Aluminum coating. Those two facts support a cautious approach: remove loose dust before any contact cleaning, avoid dry wiping a coated surface, and stop if a mark does not come off with the gentlest method you have. If you need a documented cleaning process for a production or qualification environment, request the current manufacturer guidance rather than relying on a generic article.
Storage habits for aluminum coated mirrors
Storage is where many coating problems begin, and it is also where the supplied record gives you useful physical details to work with.
- Keep the coated face away from other surfaces: Store the mirror so the Enhanced Aluminum face does not rest against packaging, foam or another optic. The beveled edge is the handling feature; the coated face is the surface to protect.
- Respect the 25.4 mm and 50.8 mm sizes: Use storage that matches the actual diameter rather than a universal case that lets the optic slide. The +0/-0.1 mm diameter tolerance means a loose compartment can allow movement and edge contact.
- Keep the second surface from becoming a grinding surface: The second surface is ground, so it is not the precision face. Still, avoid letting it rub against abrasive dust or debris that could transfer to the coated side during handling.
- Label the optic and its coating: If you store multiple mirrors, identify this one as Enhanced Aluminum so it is not confused with an uncoated or differently coated flat. The 450–2000 nm range is part of its identity and worth recording with the optic.
When to stop and ask for manufacturer guidance
Stop handling and seek current Esco guidance if the coating shows a mark you cannot remove with the gentlest approach, if the edge or bevel is damaged, or if the mirror no longer seats correctly in its mount. The supplied record does not include recoating, repair or inspection acceptance criteria, so do not assume a damaged coating can be restored or that a cosmetic mark is harmless.
The same caution applies to cleaning chemistry. Because no approved solvents or procedures are supplied here, a conservative care routine is the honest recommendation: handle by the beveled edge, keep the coated face protected, store the optic so it cannot slide, and treat the 40/20 surface and >90% reflectivity as performance to preserve rather than features to test.


